Rebuilding IRONdb Nodes

If an IRONdb node or its data is damaged or lost, its data may be rebuilt from replicas elsewhere in the cluster. This process is known as "reconstituting" a node.

Prerequisites

Reconstitution requires that at least one replica of every metric stream stored on the reconstituting node be available. A reconstitute operation cannot complete if more than W-1 nodes are unavailable, including the node being reconstituted (W is the number of write_copies configured for the current topology.)

For example, given a cluster of 10 nodes (N=10) with 3 write copies (W=3), a node may be reconstituted if at least N-(W-1), or 8, other nodes are available and healthy.

As this can be a long-running procedure, a terminal multiplexer such as tmux or screen is recommended to avoid interruption.

Reconstitute Procedure

  1. Log into the IRONdb node you wish to reconstitute as root or a privileged user. Make sure the IRONdb package is up to date. If the entire old node was replaced (e.g., due to a hardware failure), then you should repeat initial installation and then disable the service.
    1. If reconstituting within the full on-premise, Circonus Inside product, package updating has been handled automatically by the installer. No manual package installation is required. Please refer to the Circonus Inside Operations Manual for details on how this process differs for Circonus Inside.
  2. Make note of this node's topology UUID, found in the imported topology. You may need to reference this configuration on another node if the node to be reconstituted is a fresh install. The node UUID will be referred to below as <node_id>.
  3. If the IRONdb service is running, stop it.
  4. Make sure there is no lock file located at /irondb/logs/snowth.lock. If there is, remove it with the following command:
    rm -f /irondb/logs/snowth.lock
    
  5. If you repeated initial installation on this node, you may skip to the next step. Otherwise, follow this procedure to clean out any incomplete or damaged data.
    1. Run the following command to find the base ZFS dataset. This will create a shell variable, BASE_DATASET, that will be used in subsequent commands.
      BASE_DATASET=`zfs list -H -o name /irondb`
      
    2. Destroy the existing data using the following commands:
      zfs destroy -r $BASE_DATASET/data
      zfs destroy -r $BASE_DATASET/text
      zfs destroy -r $BASE_DATASET/hist
      zfs destroy -r $BASE_DATASET/raw_db
      zfs destroy -r $BASE_DATASET/surrogate_db
      zfs destroy -r $BASE_DATASET/metric_name_db
      zfs destroy -r $BASE_DATASET/nntbs
      
    3. Wait for the data to be completely destroyed. To do this, periodically run the following command and wait until the value for all pools reads "0".
      zpool get freeing
      
    4. Recreate the dataset structure by running the following commands:
      zfs create $BASE_DATASET/data
      zfs create $BASE_DATASET/hist
      zfs create $BASE_DATASET/text
      zfs create -o logbias=throughput $BASE_DATASET/raw_db
      zfs create -o logbias=throughput $BASE_DATASET/surrogate_db
      zfs create $BASE_DATASET/metric_name_db
      zfs create $BASE_DATASET/nntbs
      
    5. Run the following commands to make the node-id subdirectories:
      mkdir /irondb/hist/<node_id>
      mkdir /irondb/text/<node_id>
      mkdir /irondb/data/<node_id>
      mkdir /irondb/raw_db/<node_id>
      mkdir /irondb/surrogate_db/<node_id>
      mkdir /irondb/metric_name_db/<node_id>
      mkdir /irondb/nntbs/<node_id>
      
    6. Make sure that all the directories are owned by the nobody user by running the following:
      chown -R nobody:nobody /irondb/
      
  6. Run IRONdb in reconstitute mode using the following command:
    /opt/circonus/bin/irondb-start -B
    
  7. Wait until the reconstitute operation has fetched 100% of its data from cluster peers. You can access the current percentage done at:
    <node ip address>:<node port>/stats.json
    
    ...and looking at the "reconstitute" stats.

NOTE: There may not be messages appearing on the console while this runs. This is normal. Do not stop the reconstitute.

Current progress will be saved - if the process stops for any reason, everything should pick back up approximately where it was.

If the download stops partway for any reason, you may resume it with the same command:

/opt/circonus/bin/irondb-start -B

Once the reconstituting node has retrieved all of its data, you will see the following on the console:

Reconstitute Finished!

Start the IRONdb service.

results matching ""

    No results matching ""